IntroSo guys, after logically thinking about how my xim curves work, i realized that using exponential ramp wont add any better micro movements because you are still jumping from 0% movement to 2%, then to 4% and so on so all expo does is makes it harder to track up close. The reason people thought exponential ramp was good is because a mix of the "placebo effect" and the fact that i used much more data to create the translation... However, this linear curve is actually a strait line so it is a very accurate 1:1 translation, and since it is a strait line that also means u can use other curves on top of this one!

Ingame settings100 100 sens

linear ramp

0 aim ease in

0 smoothing

(aim assist is personal so experiment)

100% ashe ads sens (or if not using a aux use 61.4% for 1:1 movement)

66.7% widow/ana ads sens (or if not usint a aux use 45.2% for 1:1 movement)

Xim settingsGeneric Alpha Config

17.2 sens

Default sync

0 smoothing

1.44 xy ratio

0 steady aim

4915 boost for xbox, 3327 boost for ps4

0% SAB

1k polling rate

Aux for snipers:

Activated with right click

(delay is optional)

10.32 sens (For perfect 1:1 sens, multiply your xim sens by .614 for ashe and .452 for widow/ana if using separate auxes, as well as 100% relative aim sens for each. If using 1 aux for snipers, multiply your sens by .614 and then put your ingame ashe sensitivity to 100% and your widow/ana sens to 73.6%)

0 smoothing

default sync

1.44 xy ratio

boost value of 4915 xbox, boost value of 3327 for ps4

Mouse settings12k dpi

1k polling rate

CurveCopy and paste this curve into the editor, and on any auxes you have for xbox:

>>> XIM APEX [Translate Ballistics] START COPY >>>

X5BC:AAAAqgFUAf4CqANSA/wEpgVQBfoGpAdOB/gIoglMCfYKoAtKC/QMng1IDfIOnA9GD/AQmhFEEe4SmBNCE+wUlhVAFeoWlBc+F+gYkhk8GeYakBs6G+Qcjh04HeIejB82H+AgiqE0:X5BC

<<< XIM APEX END COPY <<<

Copy and paste this curve for ps4 (thanks to jeff87356 for making it and finding the ps4 data):

>>> XIM APEX [Translate Ballistics] START COPY >>>

X5BC:AAAAtAFoAhwC0AOEBDgE7AWgBlQHCAe8CHAJJAnYCowLQAv0DKgNXA4QDsQPeBAsEOARlBJIEvwTsBRkFRgVzBaAFzQX6BicGVAaBBq4G2wcIBzUHYgePB7wH6QgWCEMIcAidKMo:X5BC

<<< XIM APEX END COPY <<<

How to use another curve with this configSo to use another curve, you will need to do some math. What you are going to do is paste the curve you want into a ballistic editor and copy all the data points down on a piece of paper in order from left to right. Now, multiply every single one of these points by (0.85 for xbox, and .90 for ps4) to get the new value you are going to enter into your xim ballistic curve. (for example, if my first point is 0 and my 2nd point is 3 in the curve i want to update, i will do the equation "3*.85" which equals 2.55, so now in the xim editor, my starting value will be 0, and my next curve value will be 2.55.).Repeat this process until you translate the whole curve into your xim editor, this will now look like a flattened curve, and will work the exact same was as if u used an official config

Join my discord at:

https://discord.gg/tbuD8RPAnd view my other configs at:

https://community.xim.tech/index.php?topic=87456