MW Advanced Setup (20200905)

[Tuckerpwns]

Obie and rml at 250 do u still think gunners curve and 16k dpi is good or lower the dpi?

[RML]

You are absolutely right RML I have come to realize the best polling rates for BR mode are 500hz and 250hz on the xim. 250hz is best experience on Sync Off. 500 works better with Default and Common. 500hz on Sync off is still somewhat sketchy “stuttery”.  I have completely removed Smoothing because all it really does is give me a darn headache with the floatiness. I must admit though the curves that Gunner uses 3.1 and 4.1 work really well in Warzone. 500hz Xim works Best in MP on Sync OFF.

I don’t doubt this a bit. To this day I haven’t played more then a dozen or so matches in Warzone as I keep going back to PUBG for the BR experience, I also hate changing HZ around for different games and game types. I’ve tried 250 and it feels good but makes AA too much to handle for me personally in a lot of games.

[Obie_1_Kenobi]

You are absolutely right RML I have come to realize the best polling rates for BR mode are 500hz and 250hz on the xim. 250hz is best experience on Sync Off. 500 works better with Default and Common. 500hz on Sync off is still somewhat sketchy “stuttery”.  I have completely removed Smoothing because all it really does is give me a darn headache with the floatiness. I must admit though the curves that Gunner uses 3.1 and 4.1 work really well in Warzone. 500hz Xim works Best in MP on Sync OFF.

I don’t doubt this a bit. To this day I haven’t played more then a dozen or so matches in Warzone as I keep going back to PUBG for the BR experience, I also hate changing HZ around for different games and game types. I’ve tried 250 and it feels good but makes AA too much to handle for me personally in a lot of games.

I concur I was testing different polls on different sync’s for the game to run smoother however Warzone is just a bad experience overall at the moment. We need some stability fixes for xbox. But yes besides testing to achieve better gameplay you get the added AA running 250hz.

[Riff-Raff]

How would I make the conversion of these settings to the XIM 4?  Any help would be appreciated.  Thanks!

[Tuckerpwns]

Obie when referring to gunners 3.1 and sync off at 500 are u using full maxed out dpi 12-16-20k? Also u mentioned something about bringing xim down to 250hx what’s your experience so far and at what dpi setting have you seen the beat?
Tha ks

[AlteredBeast626]

Can you post your latest configuration with this new changes please. Thank you!!

[Obie_1_Kenobi]

Obie when referring to gunners 3.1 and sync off at 500 are u using full maxed out dpi 12-16-20k? Also u mentioned something about bringing xim down to 250hx what’s your experience so far and at what dpi setting have you seen the beat?
Tha ks

Actually No. High Dpi is a no no in warzone. It’s too unstable IMO. You can try High Dpi with sync off but I would suggest trying polls on the xim below 500.  You can utilize 500 but would suggest Default Sync or Common. The curves gunner uses are actually RML curves. The curves work well with any config.  The best experience so far I have had in Warzone was using 4000dpi polling at 250hz Sync OFF and actually added 3.1 to hip and 4.1 curve to ADS. Its weird. I use the curves on my GPRO but I don’t use them on my Razer mouse. I just left my mouse at 1000hz. I am still working on different variations/combos because I want to get it near perfect. I would recommend using dpi’s as XIM suggest of 3000-4000 for Warzone. Even though some would say Polling your mouse to your xim is beneficial I found it to be more of a hinderance thus leaving my mouse at 1000hz. I noticed a slight difference but enough to leave my mouse at 1000hz.

[Tuckerpwns]

Yea I’ve found 4000 dpi at common or off with either rml 3.1/4.1 or Rml curve on this forum but I noticed when I try to go to 250 on xim and 1000 mouse my apex keeps saying hertz error on mouse despite rebooting my xim and app

[Tuckerpwns]

The game is so inconsistent with their terrible servers I’m contemplating re learning controller

[Obie_1_Kenobi]

The only reason you would have an error is if your mouse is polling lower than the xim. I would double check your mouse software and make sure it is above it.

Indeed every game will be different. You will get good servers and bad servers. Do you have a netduma router? I would suggest to buy one that way you can limit yourself on where you are connecting to.

[Tuckerpwns]

So I’m playing on the same settings we talked about either off at 4K with rml 3.1/4.1 or RML’s aggressive curve on this forum.. my issue is on 3.1/4.1 my aim is slightly too sticky due to rotational aim assist and I over exaggerate when trying to move thru the bubble, or RML’s aggressive curve is too aggressive and I exit the bubble too fast for micro movements lol

[RML]

So I’m playing on the same settings we talked about either off at 4K with rml 3.1/4.1 or RML’s aggressive curve on this forum.. my issue is on 3.1/4.1 my aim is slightly too sticky due to rotational aim assist and I over exaggerate when trying to move thru the bubble, or RML’s aggressive curve is too aggressive and I exit the bubble too fast for micro movements lol

Lower the peak of the curve until you stop over aiming. 

[Tuckerpwns]

The legend of the AA world speaks!!! Thanks RML

[AlteredBeast626]

Ok, I know that I have ask this question. But, when you post “Updated OP” I can’t locate the new changes you made to your OP. Can anyone help me find out the new configuration please!

[milkman]

First page! All new OP configuration are updated there.