[APEX] EXTREME - Perfect Match -02- ADVANCED (FINAL) MJFame Config

[chimerajr]

I’m not sure what I’m doing wrong, I’ve set all my settings to what’s in the OP, but there is so much pixel skipping no matter how much I lower or higher the ballistic curve. It’s unusable.

Does anyone have a video of how to set this up, I must be missing something. Or is this not specifically great for pixel tracking?

I’m trying it on Apex Legends.

https://youtu.be/GXHKx9CxH-U

[Opioids]

Even at 700 dpi with no curve adjustment the speed is way too fast for an arm Aimer like me anyone else running into this issue? Had to change the hip from 500 to around 350 but now I’m getting some stuttering.

[Sequ3l]

Thx MJ

This setup is just so @#$% perfect and I just can't play without using it in all my shooter games.

If you have not tryet this setup yet then do it, it's perfection

[hurtmep1nty]

THoughts on using this for Apex Legends?

[Wickedz]

Hi,

Anyone, using this config on Apex Legends ?

[Od1n]

Hi,

Anyone, using this config on Apex Legends ?

It works pretty good with Apex Legends, same can be said for most other games.
Overall its an interesting config that is worth it to try.

[Wickedz]

Hi Od1n,

I'll give it a try then

Thank you 

[TurboMan]

Thank you for this config man, switched to it this week and I've been deadly accurate, my KD on BO4 Blackout has jumped! I'm a pretty low sens player with 40cm HIP 50cm ADS sensitivities.
With those sens' I didn't need to boost the ballistic curves at all really (boosted ADS just a smidge just now actually after noticing just a bit of undertracking at times), so I do get loads of aim assist, but I actually love the aim assist as I've been so accurate with it. You just need to learn to flick through the bubble at times, but the consistency it gives me has been brilliant. Bullet reg seems much better with more aim assist as well. I've been using a mouse and XIM since like October and been using all the features to try to fight the aim assist for more accuracy, but I've since learned that if I just utilise the aim assist fully then overall I'm a much, much more consistent player.

[InZane]

I may be a little late to the show but I've been testing this method for a couple of days now. Works great imo but I'm not sure if I have done the ads curve right. I had to clear the ads curve to get low enough ads sens, isn't that defeating the whole point of the config?
Am I doing something wrong?

[Od1n]

I may be a little late to the show but I've been testing this method for a couple of days now. Works great imo but I'm not sure if I have done the ads curve right. I had to clear the ads curve to get low enough ads sens, isn't that defeating the whole point of the config?
Am I doing something wrong?

Thats just fine, you happen to play with slower sensitivities so thats to be expected. The curve is just there to expand the sensitivity range for those that need it.
You could go 500hz instead of 1000hz as that would double your sensitivity since you use sync off if you want to make use out of the curve.

[InZane]

I may be a little late to the show but I've been testing this method for a couple of days now. Works great imo but I'm not sure if I have done the ads curve right. I had to clear the ads curve to get low enough ads sens, isn't that defeating the whole point of the config?
Am I doing something wrong?

Thats just fine, you happen to play with slower sensitivities so thats to be expected. The curve is just there to expand the sensitivity range for those that need it.
You could go 500hz instead of 1000hz as that would double your sensitivity since you use sync off if you want to make use out of the curve.

Allright, good to hear. I will try 500hz and play around with the curve soon

[TurboMan]

Thats just fine, you happen to play with slower sensitivities so thats to be expected. The curve is just there to expand the sensitivity range for those that need it.
You could go 500hz instead of 1000hz as that would double your sensitivity since you use sync off if you want to make use out of the curve.

If it doubled their sensitivity then they'd have to lower it to 250 and then they still wouldn't be able to utilise the curve though, correct?

[Od1n]

Thats just fine, you happen to play with slower sensitivities so thats to be expected. The curve is just there to expand the sensitivity range for those that need it.
You could go 500hz instead of 1000hz as that would double your sensitivity since you use sync off if you want to make use out of the curve.

If it doubled their sensitivity then they'd have to lower it to 250 and then they still wouldn't be able to utilise the curve though, correct?

That may be the case, yes.
But ultimately the config isnt only about the curve, the main idea is to use the maximum xim sensitivity with 20 smoothing and a high sync. The curve is then used to adjust the xim sensitivity. For the config it doesnt matter if the curve boosts or reduces your xim sensitivity, the outcome is pretty much the same.
So if you have to use 250hz to use a boosted curve then id actually recommend to use 500-1000hz and use the default curve or reduce the mouse sensitivity via the curve.

[TurboMan]

That may be the case, yes.
But ultimately the config isnt only about the curve, the main idea is to use the maximum xim sensitivity with 20 smoothing and a high sync. The curve is then used to adjust the xim sensitivity. For the config it doesnt matter if the curve boosts or reduces your xim sensitivity, the outcome is pretty much the same.
So if you have to use 250hz to use a boosted curve then id actually recommend to use 500-1000hz and use the default curve or reduce the mouse sensitivity via the curve.

Interesting, thanks. I use this config at 1000hz with a default curve and 453 HIP 435 ADS. Might try putting them both to 500 and reducing the sens via the curves instead.

Would the sensitivity be perfectly matched if, for example in my case, I increased my HIP sensitivity from 453 to 500 meaning a 9.86% increase, so I then lowered the top end of the curve by that same 9.86%, so from 100 to 90.14?

[Od1n]

Interesting, thanks. I use this config at 1000hz with a default curve and 453 HIP 435 ADS. Might try putting them both to 500 and reducing the sens via the curves instead.

Would the sensitivity be perfectly matched if, for example in my case, I increased my HIP sensitivity from 453 to 500 meaning a 9.86% increase, so I then lowered the top end of the curve by that same 9.86%, so from 100 to 90.14?

Yes that should allow you to end up with the same sensitivity as before