XIM Community

Tut: USB -> DualShock 4 adapter mod (W11cE Device)  (Read 109755 times)

Offline riggidy

  • Member
  • *
  • Posts: 128
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #450 on: 11:17 AM - 02/04/14 »
I just tested it, the chat works fine although it appears nobody talks in bf4. 

Took me 10 squads to actually get someone to respond to a simple hello.  Lol

Anyways, the speaker icon shows me transmitting and i could hear the other players

Offline roads

  • MVP
  • *
  • Posts: 19559
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #451 on: 11:19 AM - 02/04/14 »
Yes nobody talking is strange in BF4.
Crusade atm: none

Offline sp0t619

  • Member
  • *
  • Posts: 302
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #452 on: 01:50 PM - 02/04/14 »
I agree, I only chat with friends in a party anyway.

Do you guys think 24 awg will rise shorting the 5v and gnd connections? I got sent the wrong ones and was gonna start on it today.

Offline riggidy

  • Member
  • *
  • Posts: 128
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #453 on: 02:24 PM - 02/04/14 »
I use 26 awg.  The 24 i tried was a little too stiff to work with but it will work fine if you are careful.  You can try cutting a few strands off the wire so its smaller.

Offline W11cE

  • MVP
  • *
  • Posts: 1532
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #454 on: 02:34 PM - 02/04/14 »
Anyone that used the teensy 3.1 board.. Did you use the most recent 1.18 RC2 software for all this?
I have used only 1.17, but 1.18 RC2 should be fine too.

Another question, will the ds4 chat cable line-in at the bottom of the ds4 Controller work after its modded? I have a headset that plugs into it..
Yes it will work.

I agree, I only chat with friends in a party anyway.

Do you guys think 24 awg will rise shorting the 5v and gnd connections? I got sent the wrong ones and was gonna start on it today.
You should be fine as long you dont remove green mask from grounding. If you do the mask removing carefully you cant short circuit those even with poor soldering skills.

I have voice chat turned off in BF4 settings. Why would i want to communicate with strangers ?

Offline sp0t619

  • Member
  • *
  • Posts: 302
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #455 on: 04:01 AM - 02/05/14 »
Ok, got all wires soldered.. Now a few problems..

I connect ds4 to pc,  with Xbox 360 controller in USB shield.. I get player 1 on Xbox controller. Ds4 triangle is blinking.

I open up joy.cpl and every button is working Except for my Left stick press (L3). Its connected to pin 29.

And also,  my cross hair is on the top left corner. Not centered.. How to fix this?

Offline roads

  • MVP
  • *
  • Posts: 19559
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #456 on: 04:12 AM - 02/05/14 »
Quote
How to fix this?

Find the soldering fault. You can also check the output window to narrow down the fault to the MCP that doesn’t work. Worst time you have doing this mod.
L3 // on the using pin 33 in the firmware?
Calibrated?
Crusade atm: none

Offline sp0t619

  • Member
  • *
  • Posts: 302
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #457 on: 05:04 AM - 02/05/14 »
Whats the calibration process?

Offline roads

  • MVP
  • *
  • Posts: 19559
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #458 on: 05:17 AM - 02/05/14 »
connect ds4 to USB on DS4 wait 5 secs. Best is to check in viewer while you do this.
Crusade atm: none

Offline sp0t619

  • Member
  • *
  • Posts: 302
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #459 on: 05:31 AM - 02/05/14 »
I've had the ds4 calibrated with my ps4 before I started the mod.. Would I have to do it again?

Offline roads

  • MVP
  • *
  • Posts: 19559
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #460 on: 05:41 AM - 02/05/14 »
So you were calibrating imaginary pots (MCPs). You are planning to play ghosts, right? Sorry had to take this :D
Yes you calibrate when the mod is done.
Crusade atm: none

Offline sp0t619

  • Member
  • *
  • Posts: 302
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #461 on: 07:08 AM - 02/05/14 »
Sorry, after 10 hours of soldering and prepping up wires I must've inhaled a ton of lead to go this crazy.

Anyways, I got it all working! In joy.cpl is the cross hair supposed to be staying still? Mine is in the center but its moving.

Offline roads

  • MVP
  • *
  • Posts: 19559
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #462 on: 07:18 AM - 02/05/14 »
try with a game, BF4 test-range is where I test.
Crusade atm: none

Offline sp0t619

  • Member
  • *
  • Posts: 302
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #463 on: 07:48 AM - 02/05/14 »
Is it teensy to ps4? Or ds4 to ps4?

Offline roads

  • MVP
  • *
  • Posts: 19559
    • View Profile
Re: Tut: USB -> DualShock 4 adapter mod (WIP)
« Reply #464 on: 08:00 AM - 02/05/14 »
its shield to triangle
Crusade atm: none


Admin