XIM Community

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Oneirophrenia

Pages: 1 [2] 3
16
Technical Support / Re: [ACTIVE] Bf4 - Help
« on: 10:16 AM - 09/13/14 »
I have only profile and I did set up my mouse second time yesterday that time I posted picture . pressing the button behind the scroll wheel doesn't seen to change anything regarding mouse behavior

17
Technical Support / Re: [ACTIVE] Bf4 - Help
« on: 07:23 AM - 09/13/14 »
I only have one config . I only play one game . ADS is set up for hold and not toggle .
Pressing DPI button does not change anything for mouse behavior .

18
Technical Support / Re: [ACTIVE] Bf4 - Help
« on: 08:53 PM - 09/12/14 »
I only have one profile as you can see from the picture. When I press the switch profile there is one out of three lights light up . that's the only one light lights up   even if I keep pressing the DPI buttons .

19
Technical Support / Re: [ACTIVE] Bf4 - Help
« on: 07:32 PM - 09/12/14 »
Turn off auto game detection mode,that is designed for PC , I noticed that on mine, if you gave say bf4 set as auto then it will mess it up.
I never turned on the auto game detection mode. All the setting I changed were in on board memory .

20
Technical Support / Re: [ACTIVE] Bf4 - Help
« on: 07:26 PM - 09/12/14 »

That's my set up

21
Technical Support / Re: [ACTIVE] Bf4 - Help
« on: 07:25 PM - 09/12/14 »

On board profile and auto game detection mode.
I have set up everything on on board memory .

22
Technical Support / Re: [ACTIVE] Bf4 - Help
« on: 07:19 PM - 09/12/14 »
I have a thought...

By default, the Logitech mice do not save their profiles to the mouse's on-board memory.  By default, the profile loading/switching is handled by Logitech's Windows driver, not the mouse.  However, there is no Windows driver with XIM4.  So people have to remember to tell Logitech's software to save to the mouse's on-board memory.

If this hasn't been done, then your mouse's on-board memory would still have the default profiles it was programmed with at the factory.  Logitech puts a few simple profiles on the mouse so that it can be used without a driver.  So you might get profiles you are not expecting.  You might get several.  And that means you could be switching between them, even though you thought there was only one.

Does this make sense?

Short version: Try telling Logitech's software to save to on-board memory.
I know there are two way you can set up profile 1. On board memory 2. Game mode .
When i set the DPI , I set it up on board memory . I check the video from Logitech regarding setting up the DPI and stuff. I do not have any other mouse to check it with as I have not owned a desktop PC in years. 

23
Technical Support / Re: Bf4 - Help
« on: 02:31 PM - 09/11/14 »
Are you sure you're not hitting your mouse's DPI adjustment buttons?  That would 100% explain your symptoms.
No actually to avoid that issue when DPI get changed accidentally. I only kept one profile with one DPI setting .
I give it a shot with more set up . played few games on operation metro than when I quit the game and change the server . same thing . it got so sensitive that I can't control it . I reduce DPI but it didn't seem it had any effect on the sensitivity of mouse

24
Technical Support / Re: Bf4 - Help
« on: 01:27 PM - 09/11/14 »
I am giving it one more try today .

25
Technical Support / Re: Bf4 - Help
« on: 01:08 PM - 09/11/14 »
Yes I did tune my mate. 
@Aiken first day it got slow suddenly . so second day I started set up all over . so initially it worked fine than it got extremely sensitive without any change that's why I decreased the hip and ads sens.

26
Technical Support / Re: Bf4 - Help
« on: 12:31 PM - 09/11/14 »
I tried send of lower than 10 . even 1 and 0 but it doesn't help at all . first it happened.  I connected xim to pc and see if there is any update . as well as I did same with mouse . than I uninstall the xim manager completely from phone and start from scratch but it didn't resolve the issue .

27
Technical Support / [ACTIVE] Bf4 - Help
« on: 08:45 AM - 09/11/14 »
 I received my XIM4 yesterday . I set up everything according to tutorial and configure ST in manager according to video on you tube, vehicle setting according to the one described in a Forum here . I spent almost 2 hours setting up everything and button lay out . After everything first game I played was fine . But after that one game everything has been acting weird , one game movement will be so slow that I can barely play at all. so today started fresh and set up new config in manager and started over , the same thing . One or two games were fine and after that everything is extremely sensitive. I tried to reduce sensitive of HIP and ADS but its totally unplayable .
At some point I played with 0 sensitive with hip and Ads but same , i can barely aim at someone.
I have only one config in the manager.
I use G502 which I have updated in Logitech Software before I used it  with XIM , as well as I only have one profile with 12000 DPI and 1000 . 
I have tried different sensitivity but still same results.

28
What's best hip / Ads setting ??

29
XIM 4 Discussions / Re: Xim4 and waiting for destiny!
« on: 07:16 PM - 09/08/14 »
Still in the process of waiting for my XIM to get here. It's been in the Fedex sorting facility since Thursday. Gonna be using the controller for the first couple of days I think. :(
I am in the same boat . My xim is in sitting at FedEx since Friday evening . Hopefully delivery date is tomorrow. Just tuned my g502 in LGS and bought a cheap wired keyboard . Now can't wait for xim to be delivered tomorrow .

30
General Discussion / Re: Debating on a new monitor...
« on: 11:20 AM - 09/07/14 »
http://m.bestbuy.com/m/e/product/detail.jsp?skuId=5704037&pid=1219148661628&pcatId=abcat0509000
this is not the best out there but being 100$ is it worth the money .
It has 5 ms response time.
Any suggestions ??

Pages: 1 [2] 3