XIM Community

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - He4DHuNt3r

Pages: [1] 2 3 ... 77
Hardware Compatbility / Re: G305 and K63 Question
« on: 04:21 PM - 06/19/20 »
With my G305, I have to set the polling rate to 1000hz & set my XIM to 500hz for it not to stutter.

I hope next-gen has at least a performance option for higher FPS & lower resolution (1440P/1080P 120FPS)

If COD doesn't have a 120fps option on PS5 or Xbox Series X, I'll be very disappointed :-\

General Discussion / DumaOS 3.0
« on: 08:03 AM - 06/13/20 »
did you sigh up at Netgear for the xr500? I think there doing the DumaOS part.

Yeah I did, but I'm assuming they select people who are active on the forums first :-\

General Discussion / DumaOS 3.0
« on: 03:56 AM - 06/13/20 »
I got an email from NG saying I would be getting the beta next week.

Lucky! - I signed up for the R1 & XR500 beta and still haven't heard anything :(

XIM APEX Discussions / XIM Apex vs Native, COD warzone.
« on: 10:08 PM - 04/30/20 »
Native KB/M on PS4 feel's like PC, but has 1 issue that stops me from using it now.

There's a weird "Deadzone" that stops you from doing small precise aiming & you notice this especially when using sniper's in Warzone.

XIM actually does a better job with pixel aiming, even with Aim Assist disabled.

Game Support / Re: NEW ST WARZONE ???
« on: 03:58 AM - 04/30/20 »
Use the latest MW 2019 ST & use the default Deadzone in-game for your console

PS4 = 0.05

Xbox = 0.07

i was about to post about this lol, seems like stick drift could be an issue for people so will this mean a retrain of the ST is not necessary since default is .05?

The default on PC is 0.20 for some reason, I'll need to check what the default is on Xbox is now.

XIM APEX Discussions / Warzone New Patch - Deadzone Config
« on: 01:46 AM - 04/29/20 »
Yeah just noticed they added that option :o

EDIT: I can reduce the deadzone down to 0.03 without any stick drift on my DS4 v2 - Anything lower & my right stick drifts very slightly.

MW is being updated right now.

Again?? What's changed?

Beta / Re: XIM APEX BETA [Firmware 20200307] (**LATEST**)
« on: 09:38 PM - 03/08/20 »
Can confirm the issue is fixed for me also :)

Beta / Re: (BUG) Firmware 20200203
« on: 07:55 AM - 03/07/20 »
It's a bug with the new firmware, the issue goes away for me when I plug my KB/M into the XIM.

That's strange. Ok, thanks for reporting that. Sounds like all if fine as long as everything is plugged in prior to plugging in your XIM into your console?

That's correct!

I use a USB switch, So as soon as I switch my KB/M from PC to XIM the issue goes away.

Just updated to the latest firmware & noticed my XIM constantly flashes red when there's no KB/M connected.

it's showing on XIM Manager Aux10 is constantly been pressed, when I plug my KB/M into my XIM it stops showing it's been pressed & the red lights stop blinking.

It's not affecting me when I'm gaming or anything, just a weird bug I've noticed after updating ???


Strange, so if I just have my controller plugged into the XIM, it's moving my right stick upwards, I guess that's what Aux10 means on Manager (Right Thumb Stick) - Issue goes away if I plug my KB/M in.

Beta / Re: XIM APEX BETA [Firmware 20191217] (**LATEST**)
« on: 02:14 AM - 02/13/20 »
hi OBsIV,

after yesterday's MW update, a weird bug or issue I noticed.. I left my mouse idle for 10 mins while I was on MW menu and it automatically disconnected. Is there any deactivation time or power saving feature in Xim apex?
It's very random but happened twice since yesterday hence reporting.
Mouse: logitech G502 PS


Sounds like the Cable that connects your controller to the XIM Hub is faulty, try using another micro-USB cable & see if it still disconnects after 10 minutes.

Pages: [1] 2 3 ... 77