1
Game Support / Re: Overwatch Quick Profile Switching (using Nav Controller)
« on: 05:40 PM - 01/03/18 »
Great idea! I just picked one of these up, but I have no idea how to set this up or use the nav wirelessly. Could you explain?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
This is my linear setup on Xbox One:
OW Settings: 100 horizontal/vertical sens, 100 aim assist strength, 3 aim assist window (this is personal preference, but I recommend something in the 0-5 range. Linear setup does not feel very good with a large aim assist window because it becomes difficult to break into the aim assist bubble around enemy bodies), 0 aim ease in. Of course, use Linear Ramp and make sure you are not on Expo or Dual Zone
- Console Controller Crossover ST (you cannot use the official Overwatch ST with this Linear setup)
- 2000 mouse dpi, 500hz polling rate (I recently moved back to 500hz polling from 1000hz and it just feels a lot better and more consistent to me on all mice), 152.50 XIM sens (linear requires a much higher XIM sens than the usual expo ramp setup on the official OW ST). I feel like this might explain why some people feel linear is too sluggish? Perhaps you used too low XIM sens. If you want to match my XIM sens but want to use a higher mouse DPI like 12k or something, then use this DPI calculator, punch in your numbers (put my 2000 dpi & 152.50 sens in the "current DPI" & "current sensitivity" box) and put your desired DPI in the box and then use the sensitivity that it gives you as your new XIM sens.
- 1.50 Y/X ratio (absolutely necessary because vertical sens seems to be slower on the console controller crossover ST, 1.50 Y/X makes them equal)
- Use the following 12.0 curve if you are on Xbox One:Code: [Select]>>> XIM4 [Mouse Ballistics] START PASTE >>>
X4MB:AAAAGgA0AC4AMAAwAC4AMgAwADEANgAwADQAMAA1GCIsNkBKVF5ocnyGkJqkrrjCyMjI:X4MB
<<< XIM4 END PASTE <<<
Or use the following 8.0 curve if you are on PS4:Code: [Select]>>> XIM4 [Mouse Ballistics] START PASTE >>>
X4MB:AAAAGgA0AC4AMAAwAC4AMgAwADEANgAwADQAMAA1EBokLjhCTFZganR+iJKcprC6xMjI:X4MB
<<< XIM4 END PASTE <<<
NOTE: I do not have a PS4 and some people have reported that 8.0 is not enough to overcome the deadzone problem. You can see if you are having the deadzone problem by moving your mouse in VERY VERY small movements (I am talking pixel by pixel movement on screen). If you are not getting movement or getting choppy movement, then use the 8.5 curve below instead:Code: [Select]>>> XIM4 [Mouse Ballistics] START PASTE >>>
X4MB:AAAAGgA0AC4AMAAwAC4AMgAwADEANgAwADQAMAA1ERslLzlDTVdha3V/iZOdp7G7xcjI:X4MB
<<< XIM4 END PASTE <<<
These curves are strictly designed to just overcome the deadzone problem and nothing else. I am kind of wary of the above PS4 curves because since I don't have a PS4 I haven't tested them personally. If 8.5 is too high of a value, it will end up feeling floaty and you won't have a good experience. That is why I suggest trying the 8.0 first. You want to use the lowest number possible for it to feel like 1:1 mouse movement. But for Xbox One I can vouch that the 12.0 curve above is perfect for overcoming the deadzone.
Another thing that I feel is really important is to use a gold XIM firmware. By that, I mean DON'T use one of the experimental SA firmwares. There are a lot of people on these experimental firmwares and it will affect your ability to use the Linear setup properly. So use the latest official firmware found here: http://community.xim.tech/index.php?topic=49093.0
There is no need to use boost, steady aim or any of that other stuff. The curve alone fixes the deadzone issue.
I also want to mention that I use a large XL mousepad and controlled mouse movement. I don't play a whole lot of high mobility flankers like Genji/Tracer but I play a lot of hitscan like McCree and Soldier.
Much of what I said above has already been the Linear setup being suggested since the beginning but I wanted to make it more detailed so that people are using Linear PROPERLY and not writing it off immediately because they failed to set it up properly. If there is any setting I missed that you are confused about let me know.
