XIM Community

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - pyro90294

Pages: [1]
1
Shared Configs / Apex Legends Laser Setup
« on: 09:43 PM - 08/14/19 »
Amidst the flurry of Apex configs that are popping up, I thought id try my hand at assisting those who may still be having trouble. My config utilizes the G502 (older model 12k max dpi). This setup may seem absurd but the configuration plays VERY NIIICE (Borat voice) with the AA bubble in Apex. Enjoy and please leave feedback!
-Apex Legends PS4 ST
-1000hz mouse polling
-500hz Xim polling
-Default Sync for HIP & ADS
-No Curves
-HIP: Sens = 25; Smoothing = 0; Y/X = 1.0; Steady Aim = 8.6; 0 Boost
-ADS: Sens = 15; Smoothing = 0; Y/X = 1.20 (recoil management); Steady Aim = 7.5; 0 boost

In Game Settings: 7/7 Sens; Classic Response Curve; Small Look Deadzone; Small Movement Deadzone

There is no SAB value to display since I am using an analog stick from the PS NAV.
The reason for the high steady aim values is that this game allows a very high amount of aiming vector quantization (not sure if due to the games deadzone shape or the ST itself) HOWEVER, this does not come at the cost of diminished fine aim sensitivity (as aforementioned the game allows for a large amount of quantization without stuttering) so donít let those steady aim values deter you from what MAY become your favorite setup. At this time I have not tested with my DeathAdder Elite. I will do so and let you guys know! Enjoy and leave feedback!

-PS donít forget to adjust sensitivity to your liking. I am a wrist aimer with a small mousepad

2
Shared Configs / BO1 ST helps BO4 aim mechanics
« on: 03:42 PM - 05/28/19 »
Good Afternoon XIMmers. Just wanted to quickly share with you all some information regarding the fluency ive experienced utilizing the BO1 (PS3) smart translator on PS4 (Black Ops 4). I noticed that the vanilla st for BO4 has a very ďhorizontalĒ feel and controlling the vertical climb that comes with the recoil of certain guns is hard to manage even after adjusting the Y/X ratio (it may be marginal or placebo to some but ive experienced a difference). However upon utilizing the BO1 ST I noticed not only better vertical sensitivy but also ease of entering and exiting the aim assist bubble, better micro movements on screen, and and overall more fluid aim feel that seems to feel as though thereís less of a dead zone on my G502 (12k dpi version) and my Razer DeathAdder (2013). Id be more than happy to share my settings upon request and would like for you guys to try it out for yourself and see if you can emulate my experience. Happy gaming!

3
Hey guys! Just wanted to share some Vanilla settings that Iíve found success with and that feel very consistent. To start I am using a Logitech G502 Proteus Spectrum (not the hero) at 12k DPI with 1000hz polling. Using a steel series qck mousepad as well. My in-game settings are 7 HIP, 6 ADS (donít reccomend using 8 as it severely cripples the aim assist mechanic with XIM for some reason) A Classic response curve with NO look deadzone and a Small Movement Deadzone. My XIM settings are 16 Hip with 0.94 XY ratio and 30 boost with  30 SAB. 10 ADS with 1.11 XY ratio and 60 boost with 60 SAB. My Synchronization settings are on Default for both profiles and my ADS delay is set to 100 with SAT checked. I find this may be helpful: altering the SAB to be higher with the ADS profile seems to better allow me to enter and exit the AA bubble in this game with the XY ratio allowing me to compensate for vertical recoil. My SAB and Boost values being the same are purely coincidental but it feels great imo. Give these settings a go and see if it helps the somewhat nonexistent aim assist that some users have affforementioned in other posts. Slay and Pray.

Pages: [1]