XIM Community

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - robbiek

Pages: [1] 2
XIM 4 Discussions / Re: Quick qustion...
« on: 11:48 AM - 01/17/16 »
Sorry, I should have said its the G500s.  I have been saving it to the mouse, well at least i think i have...it's still there when I plug it back in on the PC.

Should i be using generic key?


XIM 4 Discussions / Quick qustion...
« on: 11:24 AM - 01/17/16 »
Has anyone managed to use the DPI buttons - my XIM doesn't pick them up. I have changed them to generic and also tried specific key strokes.


Thanks for your help. I've tried several times with out any luck. I have an Ipad 2 and based on the information on the support page,  which states iOS 8 devices (iPhone 4s and iPad 3rd-gen and above) |I'm assuming it's not supported?

Am I correct?


Thanks -  I had manually install it using ES Explorer. The battery died now, but i think you are correct - thanks for your help with the Android.

what about the Ipad 2 is that a lost cause? I'm unable to install the app manually. How do I check the version? I'm not an Apple person Android I'm an Android man - reading the small print it looks as though it's not supported?


That's correct it is the 4114 verson - but how I only  download it 10 minutes ago?

I don't mean to sound ungrateful, but you've posted the links I've been follwoing for the past two hours.

I've redone it and followed your instructions (SAME AS PREVIOUS):



Thanks for the reply.

I'm running ios 9.2

The message was connect failure (-1)


I've decided to sell my Nexus 7 but before doing so I wanted to make sure my Ipad 2 would work. I followed the instructions, but kept getting an error messages. After an hour of trying I tried to reconnect the Nexus, but this also gave errors message - "communcation size mismatch - 1". After a slight panic, I  rolled back the firmware update to 20141114. The Nexus now connects, but the Ipad as expected does not connect.

Any ideas anyone?

I followed the instructions - new download manager - new firmware - launch manager hit p button not Bluetooth.

Thansk Rob

Back again!

I've now completed FR, checked the firmware - it's up to date.

Loaded Black Ops and Gears of War ST and I still have the same problem?

Any ideas anyone? How do I go about contact support directly?


Sorry there is a tpyo in my first post.

When using other ST the mouse works fine. I've been using a XIM for the past 7 years, so I understand how they work.

However, tonight i decided to play Black Ops 2 - exact same problem. Right stick works fine on the pad, but no movement with the mouse. Loaded Advanced Warfare ST - all works fine???

Bit confused and frustrated?


Sorry I'm not being clear.

When standing still and I move the mouse i am unable to look around. However, if I use the right stick which is plugged into the Xim4 it works just fine?

However, when aiming its fine - any ideas anyone?

I loaded COD translator and walking, running and aiming very strange?

any help would be appreciated.


XIM 4 Discussions / Two button config....
« on: 03:02 PM - 01/30/15 »
Can someone help?

I'd like to program two buttons to one with a pause in between? Is this possible?

For example, Advance Warefare - to run and boost you press space and shift. I tried secondary, but you need a pause in between..can anyone help?



Commander / Two button config....
« on: 02:43 PM - 01/30/15 »
I'm trying to work out how I program the XIM4 to enable 2 buttons to bbe used at the same time.

For example, Advance Warefare to use boost when runing you hit space bar and shift. Can you program the xim, so I use one key? I've tried secondary, but you need a split second pause in the middle?

Any ideas anyone?

Yes, I am...about to try 6.32.

Pages: [1] 2