XIM Community

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - alexko79

Pages: [1] 2
1
I tried to flash on different versions of CUE, but it turned out for me only on 2.24.50. After downloading, you need to change the file extension to .EXE

2
all in order: 1. deleted the latest version of icue. 2. copied firmware 1.02 onto the keyboard using a pin. 3. installed cue 2.24.50 and launched the program as an administrator 4. disconnected the internet. 5. I flashed the keyboard file 1.02 through the cue. 6. deleted the dongle from the device manager on the computer. 7. installed the latest version of icue 8. connected the keyboard to the dongle using icue. It is possible that some of these actions were superfluous, but it worked for me.

3
but it is possible - 100%

4
Honestly, I also did not immediately work out. I tried several hours.

5
connect the key to the computer when the keyboard is off and remove it from the device manager

6
Using a small paperclip or push-pin, press down on the button inside the pinhole.
Plug your keyboard back into the computer, while holding down the pinhole button.
Once it is plugged back in, your computer should recognize a drive called CRP_Disabled. Please open this.
Download the firmware file from link. Extract this file to an easily found location on the computer.
Delete the file FIRMWARE.BIN from the CRP_DISABLED drive, and then place the file with ISP in itís name to the CRP_Disabled drive.


7
what version of cue is installed?

8
You need to download the firmware file 1.02 from the link http://www.filedropper.com/k63wirelessfirmwarev102. flash with cue 2.24.50 http://forum.corsair.com/v3/showthread.php?t=138472

9
Now on the keyboard firmware 1.02. everything is working

10
after much torment I did it. now my keyboard works again without a wire with xim apex

11
unfortunately it does not work

12
Thank you very much.
Today I will try to make a downgrade firmware. I'll write about the results

13
Firmware file that we need FIRMWARE.BIN

 You just have to copy it.

14
Hello friends,
To dump the firmware is not difficult. Description of the process is on the manufacturer's website:

HOW TO PERFORM A HARD‑RESET ON A KEYBOARD.
Many issues on our keyboards can be corrected by manually reinstalling the firmware. This should be valid on any of our RGB keyboards, or the Lux and Strafe static lighting keyboards. In order to obtain the file required, we will need you to create a ticket and request the file. We would suggest attaching a photo of the sticker on the bottom of the keyboard so that we can verify the model beforehand. It's possible we may request it before sending anything, so it's better to attach it when you make the ticket.

Please follow the directions below:

Unplug your keyboard from the computer.
Locate the small pinhole underneath your keyboard. For some, this will be located near the polling rate switch by the cable. On others, it will be located underneath on the tilt legs on the bottom of the keyboard.
Using a small paperclip or push-pin, press down on the button inside the pinhole.
Plug your mouse back into the computer, while holding down the pinhole button.
Once it is plugged back in, your computer should recognize a drive called CRP_Disabled. Please open this.
Download the firmware file from the ticket. If it is compressed into a .RAR file, please extract this file to an easily found location on the computer.
Delete the file FIRMWARE.BIN from the CRP_DISABLED drive, and then place the file with ISP in itís name to the CRP_Disabled drive.
Once you have performed the steps above, please unplug your keyboard and then plug it back in. The device will then return to normal. Please test to see if the issue reappears. If it does, please inform us on the ticket for further troubleshooting.

15
Hardware Compatbility / Re: Corsair K63 wireless
« on: 08:43 AM - 11/30/18 »
Hello,
Please, links to old firmware versions.

Pages: [1] 2