XIM Community
XIM APEX => XIM APEX Discussions => Topic started by: enricopallazzo on 11:14 AM - 01/16/22
-
Good evening, after a few days of trying I managed to get my SET to work: BELOADER + CRONUSZEN + XIM APEX.
Connections:
(https://i.ibb.co/6tnkkcc/sketch1642350335310.png) (https://ibb.co/6tnkkcc)
My hardware:
- PS5 DIGITAL
- BELOADER WITH LATEST FIRMWARE (WIFI)
- CRONUSZEN WITH LATEST FIRMWARE AVAILABLE (OUTPUT PROTOCOL ON AUTO / PS4 SPECIALTY OFF)
- XIM APEX WITH LATEST FIRMWARE AVAILABLE (1000HZ POLLING RATE)
- POWER SUPPLY (FOR HUB XIM APEX) 5V 2A
- POWER SUPPLY (FOR BELOADER) 5V 3A
- DUALSHOCK V1 FOR XIM APEX
- KEYBOARD FNATIC STREAK65
- LOGITECH G502 HERO MOUSE (SET TO 25k DPI - 1000HZ POLLING RATE)
- USB CABLES SUPPLIED WITH CRONUSZEN
I state that if I connect Beloader + Xim Apex I do not find any anomalies, I can play without disconnections, I only have a little delay due to the use of WiFi, a problem that I think I will solve by connecting beloader to a LAN ETH> USB adapter, WASD works.
If instead I connect the BELOADER + CRONUSZEN + XIM APEX I find (watch the video below) synchronization problems (I think) in the WASD keys, if I press the W key for example the first time it will work quietly, once I press W again, Xim records the pressure but does not carry out the command, same for the ASD keys.
Is it possible to do anything to avoid this? Is this a solvable problem? Will any updates come out?
Video:
https://youtu.be/oDxqwkfV6d0
-
Can u try with ps5 controller plz and let me know as im getting my beloader on monday ty . Plus in order to give power to my beloader can i use my old iphone charger ? So basically u havent connect nothing to your ps
-
It also works with the Ps5 pad although it requires more power. A 5v 3a charger is more than enough. I have not physically connected anything to the ps5 I have the problem of the wasd keys.
-
I was able to get everything to work with 0 delay
-
I was able to get everything to work with 0 delay
Yea its working flawless no issue what so ever no lag no disconnects wonderful i dont have no issue with even the wasd and no using any power adapter for beloder i have connect it direct to my ps onlyb
-
(https://i.ibb.co/c8Q0gp5/1642443840251.jpg) (https://ibb.co/c8Q0gp5)
-
Wired is also good option but no 1000 hz maybe if in future will support 1000 hz wired connexion it will bw also good like it is now the wifi connecion
-
Have tried to get this setup to work but with no luck. All firmware is up to date and have tried with the extra power pack and plugging directly into the ps5. Everything power up except for the ps5 controller not the PS4 controller. Is there any sequence on the way you plug everything up?
-
Have tried to get this setup to work but with no luck. All firmware is up to date and have tried with the extra power pack and plugging directly into the ps5. Everything power up except for the ps5 controller not the PS4 controller. Is there any sequence on the way you plug everything up?
I had the same issue till i turn off the speciality mode from the zen after everything worked try to turn off the speciality controller amd put it on auto. I think should be fine
-
What do you mean by specialty mode? Every thing light up except for the ps5 or the ps4 controller.
-
Ps4 speciality on cronuszen manager = Off
Have you powered up your hub?
-
(https://i.ibb.co/bsLyvwf/image-1.png) (https://ibb.co/bsLyvwf)
-
Ps4 speciality on cronuszen manager = Off
Have you powered up your hub?
Thank you for the help but it still doesn’t work for me. Yes my xim hub has power. What do you mean by “powered up your hub”?
-
Could you send me a picture of your cables? I meant if you provided electricity.
-
Could you send me a picture of your cables? I meant if you provided electricity.
No electricity directly to the xim hub.
I have the regular zen cord that plug into the back of it. I have the regular cord for the ps5 controller. I have originally xim HUD. I also use a USB extension cable with my Beloader. Everything power on except for the controller.
-
Got the same problem i am using a ps5 controller tho instead of a ps4. Dont know why its not working need help
-
make sure you test with a lower version of the latest firmware in the ZEN, try using the last beta listed in the list. I heard the latest firmware had some issues, not sure. Just a thought...
-
Got the same problem i am using a ps5 controller tho instead of a ps4. Dont know why its not working need help
What problem?
-
Got the same problem i am using a ps5 controller tho instead of a ps4. Dont know why its not working need help
What problem?
Honestly I have no clue, all I know is my coworker was trying to get his to work and asked me for help. After watching like 20 videos, I found a video from Letal Panda where he mentioned to downgrade if you were having issues. I downgraded the zen to the latest listed firmware with beta on it...boom! worked. Their support page is a convoluted mess and you have to register the device serial number to access their forum. I also joined their discord page...but good old GTS and tube did the trick. So far no disconnects and he can bunny hop around while shooting :)
here is his set up
DS5
G502 ------> XIM (powered) ------> ZEN left side hole, ZEN back hole to 2.0 hub----> PC with remote play -----> PS5
Nav
Not sure if this would work for anyone else, but it did for my coworker.
-
I am also trying to play Destiny under similar conditions.
The beloader was connected by wire.
I am satisfied with the response speed and mouse movement.
But it doesn't recognize the tab button.
When Zen is connected to the beloader, it is recognized as Xbox.
did you solve this?
-
Change the usb slot from a2 or a3 that u using to a1 plug your xim to a1
-
Good evening, after a few days of trying I managed to get my SET to work: BELOADER + CRONUSZEN + XIM APEX.
Connections:
(https://i.ibb.co/6tnkkcc/sketch1642350335310.png) (https://ibb.co/6tnkkcc)
My hardware:
- PS5 DIGITAL
- BELOADER WITH LATEST FIRMWARE (WIFI)
- CRONUSZEN WITH LATEST FIRMWARE AVAILABLE (OUTPUT PROTOCOL ON AUTO / PS4 SPECIALTY OFF)
- XIM APEX WITH LATEST FIRMWARE AVAILABLE (1000HZ POLLING RATE)
- POWER SUPPLY (FOR HUB XIM APEX) 5V 2A
- POWER SUPPLY (FOR BELOADER) 5V 3A
- DUALSHOCK V1 FOR XIM APEX
- KEYBOARD FNATIC STREAK65
- LOGITECH G502 HERO MOUSE (SET TO 25k DPI - 1000HZ POLLING RATE)
- USB CABLES SUPPLIED WITH CRONUSZEN
I state that if I connect Beloader + Xim Apex I do not find any anomalies, I can play without disconnections, I only have a little delay due to the use of WiFi, a problem that I think I will solve by connecting beloader to a LAN ETH> USB adapter, WASD works.
If instead I connect the BELOADER + CRONUSZEN + XIM APEX I find (watch the video below) synchronization problems (I think) in the WASD keys, if I press the W key for example the first time it will work quietly, once I press W again, Xim records the pressure but does not carry out the command, same for the ASD keys.
Is it possible to do anything to avoid this? Is this a solvable problem? Will any updates come out?
Video:
https://youtu.be/oDxqwkfV6d0
what is this what you have on your beloader ? like a power supply just for the beloader ? if yes how is it connected to the ps5 then ?
I tried connecting the zen + apex via remote control and i just cant get it to work
Ps4 Speciality off - Tried old firmwares on the zen - still not work
Connecting the zen to my pc - after i connect my xim or a controller (doesnt matter)to the zen and then i get the sound when a usb device is getting unplugged from a pc. If i connect my xim directly to my pc it works fine.
And thats about it.
Maybe u guys can help
-
Can anyone confirm if this power boost cable fits xim apex? ATOLLA 5V/3A Power Supply... https://www.amazon.co.uk/dp/B074M6588X?ref=ppx_pop_mob_ap_share
-
Can anyone confirm if this power boost cable fits xim apex? ATOLLA 5V/3A Power Supply... https://www.amazon.co.uk/dp/B074M6588X?ref=ppx_pop_mob_ap_share
That power supply should work according to this post by mist4fun.
5V 3A power adapter ([3.5mm x 1.35mm], center-positive)
https://community.xim.tech/index.php?topic=61923.msg661839#msg661839
-
(https://i.ibb.co/c8Q0gp5/1642443840251.jpg) (https://ibb.co/c8Q0gp5)
Have u tried another controller besides the V1 ?