XIM Community

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - High Sensitivity Needs

Pages: [1]
1
Support / Re: Canít reach high sensitivity. Need help
« on: 03:56 PM - 03/14/18 »
Turning slower and expecting it to turn faster is not an option either. That just doesnít work.

Try maxing out your sensitivity in game and your configurations sensitivities and compare the two. At most points the engine will reach the cap by the controller toggles. The mouse however will not reach this cap through apex

2
Support / Re: Canít reach high sensitivity. Need help
« on: 03:51 PM - 03/14/18 »
Everything will essentially have a limit. I find the apex has been more limited on most speeds than the controller is. Keep maxed out sensitivity, and max DPI Mice will never reach it through XIM. I could do a video of it for you. Also, slowing down will not work with me, Iíve successfully done a lot of competitive play and high rank ladders. I will gladly keep my reaction time on where I stand with it. But a side by side comparison on what Iím talking about will easily show. It seems that even at 500 sensitivity AIM and ADS, the apex still cannot reach some controller speeds in game. This is not a limit issue at that point when it comes to in game.

3
Support / Re: Canít reach high sensitivity. Need help
« on: 03:22 AM - 03/14/18 »
However the controller can reach some turn on a dime speeds, depending on the game

4
Support / Re: Canít reach high sensitivity. Need help
« on: 01:27 AM - 03/14/18 »
It is set to 1000hz in the application, Iíve always had the badge showing after resetting the apex for it

5
Support / Re: Canít reach high sensitivity. Need help
« on: 01:18 AM - 03/14/18 »
My DPI profile was actually switched 1200 instead of 12,000. Double checked on my pc, and now Iím good between AIM and ADS around 300-500 on my configuration app. Boost seems eratic though so Iím going to play with it a while.

6
Support / Re: Canít reach high sensitivity. Need help
« on: 01:07 AM - 03/14/18 »
I believe I have figured out my issue. Nvm.

7
Support / Re: Apex Sensitivity Messed up Now?
« on: 12:45 AM - 03/14/18 »
Havenít been a user for long but we have the same mouse. Make sure you didnít move a decimal in your configuration app, or change your dpi profile from the side buttons. Also be sure to update settings back to recommended in game each log in for certain games.

8
Support / Canít reach high sensitivity. Need help
« on: 12:40 AM - 03/14/18 »
My main issue is this, I cannot reach high sensitivity as I would be able to on a PC. I can max out requirements and adjust/tune to each game (PUBG, MH:W, Vermintide, WaW, etc.) however... it will never reach the speed I need and I believe Iím missing something. I am using the following equipment.

- G502 proteus spectrum (1000 Hz showing)
-Corsair K70
-MM300

I seem to be working fine with smoothing options, but cannot reach high sensitivity even after adjusting recommended game settings. Iíve changed my DPI, and am about to make sure Iím not missing the 12,000 mark but it should be listed by default in the last profiles on board the mouse so I donít think I am missing that. My essential goal is to reach a full 360 degree turn between 1-2 inch mouse movement. Sometimes Iím setting the configuration sensitivity to 500 and cannot reach these speeds. Yet I turn the controller toggle and can do a 720 in a fraction of the time.

Iím going to keep researching whatís going on with this and update any info needed. Maybe I should be doing an expert configuration.

Pages: [1]